rtl8812au/README.md at 217659ed42053032013287d5db2d5941ddd2c67b

mirrors/rtl8812au

Fork 0

mirror of https://github.com/aircrack-ng/rtl8812au.git synced 2024-11-25 14:44:09 +00:00

Christian B 217659ed42

Update README.md

2018-12-23 18:54:55 +01:00

4.9 KiB

Raw Blame History

RTL8812AU/21AU and RTL8814AU drivers

supports Realtek 8811, 8812, 8814 and 8821 chipsets

What's NEW

* december: working on a major update/bugfixes.
  may be seen rolling out over here https://github.com/aircrack-ng/rtl8812au/pull/246
  
* october: airmon-ng now got support for this driver (even without virtual interface support)

DKMS

This driver can be installed using [DKMS]. This is a system which will automatically recompile and install a kernel module when a new kernel gets installed or updated. To make use of DKMS, install the dkms package, which on Debian (based) systems is done like this:

$ sudo apt-get install dkms

Installation of Driver

In order to install the driver open a terminal in the directory with the source code and execute the following command:

$ sudo ./dkms-install.sh

Removal of Driver

In order to remove the driver from your system open a terminal in the directory with the source code and execute the following command:

$ sudo ./dkms-remove.sh

Make

For building & installing the driver with 'make' use

$ make
$ make install

Notes

Download

$ git clone -b v5.2.20 https://github.com/aircrack-ng/rtl8812au.git
$ cd rtl*

Package / Build dependencies (Kali)

$ sudo apt-get install build-essential
$ sudo apt-get install bc
$ sudo apt-get install libelf-dev
$ sudo apt-get install linux-headers-`uname -r`

For Raspberry (RPI 2/3)

$ sudo wget "https://raw.githubusercontent.com/notro/rpi-source/master/rpi-source" -O /usr/bin/rpi-source
$ sudo chmod 755 /usr/bin/rpi-source
$ sudo rpi-source

Then you need to

$ git clone https://github.com/aircrack-ng/rtl8812au -b v5.2.20
$ cd rtl*
$ make
$ sudo cp 8812au.ko /lib/modules/`uname -r`/kernel/drivers/net/wireless
$ sudo depmod -a
$ sudo modprobe 88XXau

then run this to change platform in Makefile

$ sed -i 's/CONFIG_PLATFORM_I386_PC = y/CONFIG_PLATFORM_I386_PC = n/g' Makefile
$ sed -i 's/CONFIG_PLATFORM_ARM_RPI = n/CONFIG_PLATFORM_ARM_RPI = y/g' Makefil

But for RPI 3 B+ you will need to run those below the ARM64 arch build

$ sed -i 's/CONFIG_PLATFORM_I386_PC = y/CONFIG_PLATFORM_I386_PC = n/g' Makefile
$ sed -i 's/CONFIG_PLATFORM_ARM64_RPI = n/CONFIG_PLATFORM_ARM64_RPI = y/g' Makefile

For setting monitor mode

Fix problematic interference in monitor mode.

$ airmon-ng check kill

You may also uncheck the box "Automatically connect to this network when it is avaiable" in nm-connection-editor. This only works if you have a saved wifi connection.

Set interface down

$ $ sudo ip link set wlan1 down

Set monitor mode

$ sudo airmon-ng start wlan#
or
$ sudo iw dev wlan# set type monitor

Set interface up

$ sudo ip link set wlan0 up

For setting TX power

$ sudo iwconfig wlan0 txpower 30
or
$ sudo iw wlan0 set txpower fixed 3000

LED control

You can now control LED behaviour statically by Makefile, for example:

CONFIG_LED_ENABLE = n

value can be y or n

statically by module parameter in /etc/modprobe.d/8812au.conf or wherever, for example:

options 88XXau rtw_led_enable=0

value can be 0 or 1

or dynamically by writing to /proc/net/rtl8812au/$(your interface name)/led_enable, for example:

$ echo "0" > /proc/net/rtl8812au/$(your interface name)/led_enable