7.4 KiB
RTL8812AU/21AU and RTL8814AU drivers
Only for use with Linux & Android
Supports
* Monitor mode
* Frame injection
* WPA3 SAE
* Wi-Fi Direct
* Hostapd
* Kernel up to v5.3+
* RTKMPtool for low level debug
TODO
* Test & fix the 8821au support
* Clean out Windows & FreeBSD code
* Clean out unsupported chipsets
IPERF3 benchmark
[Device] Alfa Networks AWUS036ACH
[Chipset] 8812au (rtl8812au)
[Branch] v5.6.4.1
[Distance] 10m free sight
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 11.6 MBytes 97.4 Mbits/sec 0 96.2 KBytes
[ 5] 1.00-2.00 sec 11.2 MBytes 93.8 Mbits/sec 0 100 KBytes
[ 5] 2.00-3.00 sec 11.2 MBytes 93.8 Mbits/sec 0 100 KBytes
[ 5] 3.00-4.00 sec 11.2 MBytes 93.8 Mbits/sec 0 100 KBytes
[ 5] 4.00-5.00 sec 11.2 MBytes 93.8 Mbits/sec 0 100 KBytes
[ 5] 5.00-6.00 sec 11.4 MBytes 95.9 Mbits/sec 0 105 KBytes
[ 5] 6.00-7.00 sec 11.2 MBytes 93.8 Mbits/sec 0 105 KBytes
[ 5] 7.00-8.00 sec 11.3 MBytes 94.9 Mbits/sec 0 157 KBytes
[ 5] 8.00-9.00 sec 11.2 MBytes 93.8 Mbits/sec 0 157 KBytes
[ 5] 9.00-10.00 sec 11.2 MBytes 94.3 Mbits/sec 0 157 KBytes
[ 5] 10.00-11.00 sec 11.2 MBytes 93.8 Mbits/sec 0 157 KBytes
[ 5] 11.00-12.00 sec 11.2 MBytes 93.8 Mbits/sec 0 157 KBytes
[ 5] 12.00-13.00 sec 11.2 MBytes 94.4 Mbits/sec 0 157 KBytes
[ 5] 13.00-14.00 sec 11.2 MBytes 93.8 Mbits/sec 0 157 KBytes
[ 5] 14.00-15.00 sec 11.2 MBytes 94.4 Mbits/sec 0 157 KBytes
[ 5] 15.00-16.00 sec 10.9 MBytes 91.7 Mbits/sec 0 157 KBytes
[ 5] 16.00-17.00 sec 11.2 MBytes 94.4 Mbits/sec 0 157 KBytes
[ 5] 17.00-18.00 sec 11.2 MBytes 94.4 Mbits/sec 0 157 KBytes
[ 5] 18.00-19.00 sec 11.2 MBytes 94.4 Mbits/sec 0 157 KBytes
[ 5] 19.00-20.00 sec 11.2 MBytes 93.8 Mbits/sec 0 157 KBytes
[ 5] 20.00-21.00 sec 11.2 MBytes 93.8 Mbits/sec 0 157 KBytes
[ 5] 21.00-22.00 sec 11.2 MBytes 93.8 Mbits/sec 0 157 KBytes
[ 5] 22.00-23.00 sec 11.2 MBytes 93.8 Mbits/sec 0 157 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-23.15 sec 260 MBytes 94.2 Mbits/sec 0 sender
[ 5] 0.00-23.15 sec 0.00 Bytes 0.00 bits/sec receiver
DKMS
This driver can be installed using [DKMS]. This is a system which will automatically recompile and install a kernel module when a new kernel gets installed or updated. To make use of DKMS, install the dkms package, which on Debian (based) systems is done like this:
sudo apt-get install dkms
Installation of Driver
In order to install the driver open a terminal in the directory with the source code and execute the following command:
sudo ./dkms-install.sh
Removal of Driver
In order to remove the driver from your system open a terminal in the directory with the source code and execute the following command:
sudo ./dkms-remove.sh
Make
For building & installing the driver with 'make' use
make
make install
Notes
Download
git clone -b v5.6.4.1 https://github.com/aircrack-ng/rtl8812au.git
cd rtl*
Package / Build dependencies (Kali)
sudo apt-get install build-essential
sudo apt-get install bc
sudo apt-get install libelf-dev
sudo apt-get install linux-headers-`uname -r`
For Raspberry (RPI)
sudo apt-get install bc raspberrypi-kernel-headers
Then run this step to change platform in Makefile, For RPI 1/2/3:
$ sed -i 's/CONFIG_PLATFORM_I386_PC = y/CONFIG_PLATFORM_I386_PC = n/g' Makefile
$ sed -i 's/CONFIG_PLATFORM_ARM_RPI = n/CONFIG_PLATFORM_ARM_RPI = y/g' Makefile
But for RPI 3B+ & 4B you will need to run those below which builds the ARM64 arch driver:
$ sed -i 's/CONFIG_PLATFORM_I386_PC = y/CONFIG_PLATFORM_I386_PC = n/g' Makefile
$ sed -i 's/CONFIG_PLATFORM_ARM64_RPI = n/CONFIG_PLATFORM_ARM64_RPI = y/g' Makefile
For setting monitor mode
- Fix problematic interference in monitor mode.
airmon-ng check kill
You may also uncheck the box "Automatically connect to this network when it is avaiable" in nm-connection-editor. This only works if you have a saved wifi connection.
- Set interface down
sudo ip link set wlan0 down
- Set monitor mode
sudo iw dev wlan0 set type monitor
- Set interface up
sudo ip link set wlan0 up
For setting TX power
sudo iw wlan0 set txpower fixed 3000
LED control
You can now control LED behaviour statically by Makefile, for example:
CONFIG_LED_ENABLE = n
value can be y or n
statically by module parameter in /etc/modprobe.d/8812au.conf or wherever, for example:
options 88XXau rtw_led_enable=0
value can be 0 or 1
or dynamically by writing to /proc/net/rtl8812au/$(your interface name)/led_enable, for example:
$ echo "0" > /proc/net/rtl8812au/$(your interface name)/led_enable
value can be 0 or 1
check current value:
$ cat /proc/net/rtl8812au/$(your interface name)/led_enable
NetworkManager
Newer versions of NetworkManager switches to random MAC address. Some users would prefer to use a fixed address. Simply add these lines below
[device]
wifi.scan-rand-mac-address=no
at the end of file /etc/NetworkManager/NetworkManager.conf and restart NetworkManager with the command:
sudo service NetworkManager restart
Credits
astsam - https://github.com/astsam aircrack-ng - https://github.com/aircrack-ng evilphish - https://github.com/evilphish fariouche - https://github.com/fariouche CGarces - https://github.com/CGarces ZerBea - https://github.com/ZerBea lwfinger - https://github.com/lwfinger Ulli-Kroll - https://github.com/Ulli-Kroll