mirror of
https://github.com/morrownr/8821cu-20210916.git
synced 2024-12-22 14:26:30 +00:00
95 lines
2.5 KiB
Markdown
95 lines
2.5 KiB
Markdown
2022-12-27
|
||
|
||
What is Concurrent Mode?
|
||
|
||
Concurrent Mode creates 2 wireless network interfaces (wlan0, wlan1) and those
|
||
two interfaces share the same WiFi adapter.
|
||
|
||
This feature allows performing 2 separate wireless tasks at the same time with a
|
||
single WiFi adapter.
|
||
|
||
For example:
|
||
|
||
Use station mode (also called managed or client mode) to connect with an
|
||
AP to access the internet at the same time as it also performs as an AP
|
||
to allow other devices to connect to the second interface.
|
||
|
||
Note: Only supports 3 combinations
|
||
|
||
1. Station mode + Station mode
|
||
2. Station mode + AP mode
|
||
3. Station mode + P2P mode
|
||
|
||
Note: Monitor mode is not supported.
|
||
|
||
-----
|
||
|
||
How do I Enable Concurrent Mode?
|
||
|
||
Edit the `Makefile` with a text editor:
|
||
|
||
```
|
||
${EDITOR} Makefile
|
||
```
|
||
|
||
Change the following line:
|
||
|
||
```
|
||
#EXTRA_CFLAGS += -DCONFIG_CONCURRENT_MODE
|
||
```
|
||
|
||
to
|
||
|
||
```
|
||
EXTRA_CFLAGS += -DCONFIG_CONCURRENT_MODE
|
||
```
|
||
|
||
and then install the driver per the installation steps. If
|
||
the driver is already installed, run the following first:
|
||
|
||
```
|
||
sudo ./remove-driver.sh
|
||
```
|
||
and then reinstall the driver with:
|
||
|
||
```
|
||
sudo ./install-driver.sh
|
||
```
|
||
|
||
Once the driver is fully installed and you have rebooted the system, you
|
||
can verify that this works by typing the “iw dev” command. You should
|
||
see two wireless interfaces, and the MAC address of the secondary interface
|
||
is nearly the same as the first except for one digit.
|
||
|
||
-----
|
||
|
||
FAQ:
|
||
|
||
Q: Which wireless interface can run in station mode? Which
|
||
wireless interface can run in AP mode?
|
||
|
||
A: It is recommended to run station mode in wlan0 and AP or P2P mode in
|
||
wlan1.
|
||
|
||
Q: How is the throughput with 2 wireless interfaces in concurrent mode?
|
||
|
||
A: Because there is only one physical hardware device, the two wireless
|
||
interfaces (wlan0, wlan1) will share the transmit bandwidth.
|
||
|
||
For example:
|
||
|
||
Assume the throughput limitation of current environment is 85Mb/s,
|
||
then the throughput of wlan0 + the throughput of wlan1 is basically
|
||
equal or smaller than 85Mb/s.
|
||
|
||
Q: Everything is fine when I only start hostapd, but when I start running
|
||
station mode in the other interface at the same time, hostapd will disconnect
|
||
for a moment then will reconnect again, however ,the channel is differ from
|
||
before. Is something wrong?
|
||
|
||
A: Don’t worry, it is fine! As mentioned before, those two wireless interfaces
|
||
share the same physical hardware device. That means those 2 wireless interfaces
|
||
must use the same channel. The AP/P2P interface should use the same channel as
|
||
the station interface. If both interfaces are running in station mode, the
|
||
connected APs MUST be on same channel.
|