2022-12-27 03:57:44 +00:00
|
|
|
|
2022-12-27
|
2022-11-28 20:27:59 +00:00
|
|
|
|
|
|
|
|
|
|
What is Concurrent Mode?
|
|
|
|
|
|
|
|
|
|
|
|
Concurrent Mode creates 2 wireless network interfaces (wlan0, wlan1) and those
|
|
|
|
|
|
two interfaces share the same WiFi adapter.
|
|
|
|
|
|
|
|
|
|
|
|
This feature allows performing 2 separate wireless tasks at the same time with a
|
|
|
|
|
|
single WiFi adapter.
|
|
|
|
|
|
|
|
|
|
|
|
For example:
|
|
|
|
|
|
|
2022-12-27 03:57:44 +00:00
|
|
|
|
Use station mode (also called managed or client mode) to connect with an
|
2022-11-28 20:27:59 +00:00
|
|
|
|
AP to access the internet at the same time as it also performs as an AP
|
|
|
|
|
|
to allow other devices to connect to the second interface.
|
|
|
|
|
|
|
|
|
|
|
|
Note: Only supports 3 combinations
|
|
|
|
|
|
|
|
|
|
|
|
1. Station mode + Station mode
|
|
|
|
|
|
2. Station mode + AP mode
|
|
|
|
|
|
3. Station mode + P2P mode
|
|
|
|
|
|
|
2022-12-27 03:57:44 +00:00
|
|
|
|
Note: Monitor mode is not supported.
|
|
|
|
|
|
|
2022-11-28 20:27:59 +00:00
|
|
|
|
-----
|
|
|
|
|
|
|
|
|
|
|
|
How do I Enable Concurrent Mode?
|
|
|
|
|
|
|
2022-12-27 03:57:44 +00:00
|
|
|
|
Edit the `Makefile` with a text editor:
|
|
|
|
|
|
|
|
|
|
|
|
```
|
2023-01-15 02:15:28 +00:00
|
|
|
|
${EDITOR} Makefile
|
2022-12-27 03:57:44 +00:00
|
|
|
|
```
|
|
|
|
|
|
|
|
|
|
|
|
Change the following line:
|
|
|
|
|
|
|
|
|
|
|
|
```
|
|
|
|
|
|
#EXTRA_CFLAGS += -DCONFIG_CONCURRENT_MODE
|
|
|
|
|
|
```
|
|
|
|
|
|
|
|
|
|
|
|
to
|
|
|
|
|
|
|
|
|
|
|
|
```
|
|
|
|
|
|
EXTRA_CFLAGS += -DCONFIG_CONCURRENT_MODE
|
|
|
|
|
|
```
|
|
|
|
|
|
|
|
|
|
|
|
and then install the driver per the installation steps. If
|
|
|
|
|
|
the driver is already installed, run the following first:
|
|
|
|
|
|
|
|
|
|
|
|
```
|
|
|
|
|
|
sudo ./remove-driver.sh
|
|
|
|
|
|
```
|
|
|
|
|
|
and then reinstall the driver with:
|
2022-11-28 20:27:59 +00:00
|
|
|
|
|
|
|
|
|
|
```
|
2022-12-27 03:57:44 +00:00
|
|
|
|
sudo ./install-driver.sh
|
2022-11-28 20:27:59 +00:00
|
|
|
|
```
|
|
|
|
|
|
|
|
|
|
|
|
Once the driver is fully installed and you have rebooted the system, you
|
2022-12-27 03:57:44 +00:00
|
|
|
|
can verify that this works by typing the “iw dev” command. You should
|
|
|
|
|
|
see two wireless interfaces, and the MAC address of the secondary interface
|
2022-11-28 20:27:59 +00:00
|
|
|
|
is nearly the same as the first except for one digit.
|
|
|
|
|
|
|
|
|
|
|
|
-----
|
|
|
|
|
|
|
|
|
|
|
|
FAQ:
|
|
|
|
|
|
|
|
|
|
|
|
Q: Which wireless interface can run in station mode? Which
|
|
|
|
|
|
wireless interface can run in AP mode?
|
|
|
|
|
|
|
|
|
|
|
|
A: It is recommended to run station mode in wlan0 and AP or P2P mode in
|
|
|
|
|
|
wlan1.
|
|
|
|
|
|
|
|
|
|
|
|
Q: How is the throughput with 2 wireless interfaces in concurrent mode?
|
|
|
|
|
|
|
|
|
|
|
|
A: Because there is only one physical hardware device, the two wireless
|
|
|
|
|
|
interfaces (wlan0, wlan1) will share the transmit bandwidth.
|
|
|
|
|
|
|
|
|
|
|
|
For example:
|
|
|
|
|
|
|
|
|
|
|
|
Assume the throughput limitation of current environment is 85Mb/s,
|
|
|
|
|
|
then the throughput of wlan0 + the throughput of wlan1 is basically
|
|
|
|
|
|
equal or smaller than 85Mb/s.
|
|
|
|
|
|
|
|
|
|
|
|
Q: Everything is fine when I only start hostapd, but when I start running
|
|
|
|
|
|
station mode in the other interface at the same time, hostapd will disconnect
|
|
|
|
|
|
for a moment then will reconnect again, however ,the channel is differ from
|
|
|
|
|
|
before. Is something wrong?
|
|
|
|
|
|
|
|
|
|
|
|
A: Don’t worry, it is fine! As mentioned before, those two wireless interfaces
|
|
|
|
|
|
share the same physical hardware device. That means those 2 wireless interfaces
|
|
|
|
|
|
must use the same channel. The AP/P2P interface should use the same channel as
|
|
|
|
|
|
the station interface. If both interfaces are running in station mode, the
|
|
|
|
|
|
connected APs MUST be on same channel.
|
