mirror of
https://github.com/morrownr/8821cu-20210916.git
synced 2024-11-04 18:45:41 +00:00
69 lines
2.1 KiB
Markdown
69 lines
2.1 KiB
Markdown
|
2021-12-03
|
|||
|
|
|
|||
|
|
What is Concurrent Mode?
|
|||
|
|
|
|||
|
|
Concurrent Mode creates 2 wireless network interfaces (wlan0, wlan1) and those
|
|||
|
|
two interfaces share the same WiFi adapter.
|
|||
|
|
|
|||
|
|
This feature allows performing 2 separate wireless tasks at the same time with a
|
|||
|
|
single WiFi adapter.
|
|||
|
|
|
|||
|
|
For example:
|
|||
|
|
|
|||
|
|
Use station mode (called managed or client mode also) to connect with an
|
|||
|
|
AP to access the internet at the same time as it also performs as an AP
|
|||
|
|
to allow other devices to connect to the second interface.
|
|||
|
|
|
|||
|
|
Note: Only supports 3 combinations
|
|||
|
|
|
|||
|
|
1. Station mode + Station mode
|
|||
|
|
2. Station mode + AP mode
|
|||
|
|
3. Station mode + P2P mode
|
|||
|
|
|
|||
|
|
-----
|
|||
|
|
|
|||
|
|
How do I Enable Concurrent Mode?
|
|||
|
|
|
|||
|
|
Run the following as instructed during the installation process:
|
|||
|
|
|
|||
|
|
```
|
|||
|
|
./cmode-on.sh
|
|||
|
|
```
|
|||
|
|
|
|||
|
|
Once the driver is fully installed and you have rebooted the system, you
|
|||
|
|
can verify that this works by typing the “iw dev” command, You should
|
|||
|
|
see two wireless interfaces, and the MAC address of secondary interface
|
|||
|
|
is nearly the same as the first except for one digit.
|
|||
|
|
|
|||
|
|
-----
|
|||
|
|
|
|||
|
|
FAQ:
|
|||
|
|
|
|||
|
|
Q: Which wireless interface can run in station mode? Which
|
|||
|
|
wireless interface can run in AP mode?
|
|||
|
|
|
|||
|
|
A: It is recommended to run station mode in wlan0 and AP or P2P mode in
|
|||
|
|
wlan1.
|
|||
|
|
|
|||
|
|
Q: How is the throughput with 2 wireless interfaces in concurrent mode?
|
|||
|
|
|
|||
|
|
A: Because there is only one physical hardware device, the two wireless
|
|||
|
|
interfaces (wlan0, wlan1) will share the transmit bandwidth.
|
|||
|
|
|
|||
|
|
For example:
|
|||
|
|
|
|||
|
|
Assume the throughput limitation of current environment is 85Mb/s,
|
|||
|
|
then the throughput of wlan0 + the throughput of wlan1 is basically
|
|||
|
|
equal or smaller than 85Mb/s.
|
|||
|
|
|
|||
|
|
Q: Everything is fine when I only start hostapd, but when I start running
|
|||
|
|
station mode in the other interface at the same time, hostapd will disconnect
|
|||
|
|
for a moment then will reconnect again, however ,the channel is differ from
|
|||
|
|
before. Is something wrong?
|
|||
|
|
|
|||
|
|
A: Don’t worry, it is fine! As mentioned before, those two wireless interfaces
|
|||
|
|
share the same physical hardware device. That means those 2 wireless interfaces
|
|||
|
|
must use the same channel. The AP/P2P interface should use the same channel as
|
|||
|
|
the station interface. If both interfaces are running in station mode, the
|
|||
|
|
connected APs MUST be on same channel.
|