## RTL8812AU/21AU and RTL8814AU drivers
### supports Realtek 8811, 8812, 8814 and 8821 chipsets
[](#)
[](#)
[](https://badge.fury.io/gh/aircrack-ng%2Frtl8812au)
[](https://github.com/aircrack-ng/rtl8812au/issues)
[](https://github.com/aircrack-ng/rtl8812au/network)
[](https://github.com/aircrack-ng/rtl8812au/stargazers)
[](https://github.com/aircrack-ng/rtl8812au/blob/master/LICENSE)
[](https://www.kali.org)
[](https://github.com/aircrack-ng/aircrack-ng)
[](https://github.com/derv82/wifite2)
### What's NEW
```
* december: working on a major update/bugfixes.
may be seen rolling out over here https://github.com/aircrack-ng/rtl8812au/pull/246
* october: airmon-ng now got support for this driver (even without virtual interface support)
*** Kernel v4.19 and v4.20 supported. ***
Also working to get both old/new kernels supported.
```
### DKMS
This driver can be installed using [DKMS]. This is a system which will automatically recompile and install a kernel module when a new kernel gets installed or updated. To make use of DKMS, install the `dkms` package, which on Debian (based) systems is done like this:
```
$ sudo apt-get install dkms
```
### Installation of Driver
In order to install the driver open a terminal in the directory with the source code and execute the following command:
```
$ sudo ./dkms-install.sh
```
### Removal of Driver
In order to remove the driver from your system open a terminal in the directory with the source code and execute the following command:
```
$ sudo ./dkms-remove.sh
```
### Make
For building & installing the driver with 'make' use
```
$ make
$ make install
```
### Notes
Download
```
$ git clone -b v5.2.20 https://github.com/aircrack-ng/rtl8812au.git
$ cd rtl*
```
Package / Build dependencies (Kali)
```
$ sudo apt-get install build-essential
$ sudo apt-get install bc
$ sudo apt-get install libelf-dev
$ sudo apt-get install linux-headers-`uname -r`
```
For Raspberry (RPI 2/3) you will need kernel sources
```
$ sudo wget "https://raw.githubusercontent.com/notro/rpi-source/master/rpi-source" -O /usr/bin/rpi-source
$ sudo chmod 755 /usr/bin/rpi-source
$ sudo rpi-source
```
Then you need to download and compile the driver on the RPI
```
$ git clone https://github.com/aircrack-ng/rtl8812au -b v5.2.20
$ cd rtl*
$ make
$ sudo cp 8812au.ko /lib/modules/`uname -r`/kernel/drivers/net/wireless
$ sudo depmod -a
$ sudo modprobe 88XXau
```
then run this step to change platform in Makefile, For RPI 2/3:
```
$ sed -i 's/CONFIG_PLATFORM_I386_PC = y/CONFIG_PLATFORM_I386_PC = n/g' Makefile
$ sed -i 's/CONFIG_PLATFORM_ARM_RPI = n/CONFIG_PLATFORM_ARM_RPI = y/g' Makefil
```
But for RPI 3 B+ you will need to run those below
which builds the ARM64 arch driver:
```
$ sed -i 's/CONFIG_PLATFORM_I386_PC = y/CONFIG_PLATFORM_I386_PC = n/g' Makefile
$ sed -i 's/CONFIG_PLATFORM_ARM64_RPI = n/CONFIG_PLATFORM_ARM64_RPI = y/g' Makefile
```
For setting monitor mode
1. Fix problematic interference in monitor mode.
```
$ airmon-ng check kill
```
You may also uncheck the box "Automatically connect to this network when it is avaiable" in nm-connection-editor. This only works if you have a saved wifi connection.
2. Set interface down
```
$ $ sudo ip link set down
```
3. Set monitor mode
```
$ sudo airmon-ng start
or
$ sudo iw dev set type monitor
```
4. Set interface up
```
$ sudo ip link set up
```
For setting TX power
```
$ sudo iwconfig txpower 30
or
$ sudo iw nset txpower fixed 3000
```
### LED control
#### You can now control LED behaviour statically by Makefile, for example:
```sh
CONFIG_LED_ENABLE = n
```
value can be y or n
#### statically by module parameter in /etc/modprobe.d/8812au.conf or whatever, example:
```sh
options 88XXau rtw_led_enable=0
```
value can be 0 or 1
#### or dynamically by writing to /proc/net/rtl8812au/$(your interface name)/led_enable, for example:
```sh
$ echo "0" > /proc/net/rtl8812au/$(your interface name)/led_enable
```
value can be 0 or 1
#### check current value:
```sh
$ cat /proc/net/rtl8812au/$(your interface name)/led_enable
```
### NetworkManager
Newer versions of NetworkManager switches to random MAC address. Some users would prefer to use a fixed address.
Simply add these lines below
```
[device]
wifi.scan-rand-mac-address=no
```
at the end of file /etc/NetworkManager/NetworkManager.conf and restart NetworkManager with the command:
```
$ sudo service NetworkManager restart
```