## RTL8812AU/21AU and RTL8814AU drivers
## with monitor mode and frame injection

[![Monitor mode](https://img.shields.io/badge/monitor%20mode-working-brightgreen.svg)](#)
[![Frame Injection](https://img.shields.io/badge/frame%20injection-working-brightgreen.svg)](#)
[![GitHub version](https://badge.fury.io/gh/aircrack-ng%2Frtl8812au.svg)](https://badge.fury.io/gh/aircrack-ng%2Frtl8812au)
[![GitHub issues](https://img.shields.io/github/issues/aircrack-ng/rtl8812au.svg)](https://github.com/aircrack-ng/rtl8812au/issues)
[![GitHub forks](https://img.shields.io/github/forks/aircrack-ng/rtl8812au.svg)](https://github.com/aircrack-ng/rtl8812au/network)
[![GitHub stars](https://img.shields.io/github/stars/aircrack-ng/rtl8812au.svg)](https://github.com/aircrack-ng/rtl8812au/stargazers)
[![GitHub license](https://img.shields.io/github/license/aircrack-ng/rtl8812au.svg)](https://github.com/aircrack-ng/rtl8812au/blob/master/LICENSE)

### What's NEW
```
* december: working on a major update/bugfixes.
  may be seen rolling out over here https://github.com/aircrack-ng/rtl8812au/pull/246
  
* october: airmon-ng now got support for this driver (even without virtual interface support)
```

### DKMS
This driver can be installed using [DKMS]. This is a system which will automatically recompile and install a kernel module when a new kernel gets installed or updated. To make use of DKMS, install the `dkms` package, which on Debian (based) systems is done like this:
```
$ sudo apt-get install dkms
```

### Installation of Driver
In order to install the driver open a terminal in the directory with the source code and execute the following command:
```
$ sudo ./dkms-install.sh
```

### Removal of Driver
In order to remove the driver from your system open a terminal in the directory with the source code and execute the following command:
```
$ sudo ./dkms-remove.sh
```

### Make
For building & installing the driver with 'make' use
```
$ make
$ make install
```

### Notes
Download
```
$ git clone -b v5.2.20 https://github.com/aircrack-ng/rtl8812au.git
$ cd rtl*
```
Package / Build dependencies (Kali)
```
$ sudo apt-get install build-essential
$ sudo apt-get install bc
$ sudo apt-get install libelf-dev
$ sudo apt-get install linux-headers-`uname -r`
```
For Raspberry (RPI 2/3)
```
$ sudo wget "https://raw.githubusercontent.com/notro/rpi-source/master/rpi-source" -O /usr/bin/rpi-source
$ sudo chmod 755 /usr/bin/rpi-source
$ sudo rpi-source 
```
Then you need to
```
$ git clone https://github.com/aircrack-ng/rtl8812au -b v5.2.20
$ cd rtl*
$ make
$ sudo cp 8812au.ko /lib/modules/`uname -r`/kernel/drivers/net/wireless
$ sudo depmod -a
$ sudo modprobe 88XXau
```
then run this to change platform in Makefile
```
$ sed -i 's/CONFIG_PLATFORM_I386_PC = y/CONFIG_PLATFORM_I386_PC = n/g' Makefile
$ sed -i 's/CONFIG_PLATFORM_ARM_RPI = n/CONFIG_PLATFORM_ARM_RPI = y/g' Makefil
```
But for RPI 3 B+ you will need to run those below
the ARM64 arch build
```
$ sed -i 's/CONFIG_PLATFORM_I386_PC = y/CONFIG_PLATFORM_I386_PC = n/g' Makefile
$ sed -i 's/CONFIG_PLATFORM_ARM64_RPI = n/CONFIG_PLATFORM_ARM64_RPI = y/g' Makefile
```

For setting monitor mode
  1. Fix problematic interference in monitor mode. 
  ```
  $ airmon-ng check kill
  ```
  You may also uncheck the box "Automatically connect to this network when it is avaiable" in nm-connection-editor. This only works if you have a saved wifi connection.
  
  2. Set interface down
  ```
  $ $ sudo ip link set wlan1 down
  ``` 
  3. Set monitor mode
  ```
  $ sudo airmon-ng start wlan#
  or
  $ sudo iw dev wlan# set type monitor
  ```
  4. Set interface up
  ```
  $ sudo ip link set wlan0 up
  ```
For setting TX power
```
$ sudo iwconfig wlan0 txpower 30
or
$ sudo iw wlan0 set txpower fixed 3000
```
### LED control

#### You can now control LED behaviour statically by Makefile, for example:

```sh
CONFIG_LED_ENABLE = n
```
value can be y or n

#### statically by module parameter in /etc/modprobe.d/8812au.conf or wherever, for example:

```sh
options 88XXau rtw_led_enable=0
```
value can be 0 or 1


#### or dynamically by writing to /proc/net/rtl8812au/$(your interface name)/led_enable, for example:

```sh
$ echo "0" > /proc/net/rtl8812au/$(your interface name)/led_enable
```
value can be 0 or 1

#### check current value:

```sh
$ cat /proc/net/rtl8812au/$(your interface name)/led_enable
```

### NetworkManager

Newer versions of NetworkManager switches to random MAC address. Some users would prefer to use a fixed address. 
Simply add these lines below
```
[device]
wifi.scan-rand-mac-address=no
```
at the end of file /etc/NetworkManager/NetworkManager.conf and restart NetworkManager with the command:
```
$ sudo service NetworkManager restart
```