mirror of
https://github.com/aircrack-ng/rtl8812au.git
synced 2024-11-23 05:44:40 +00:00
195 lines
18 KiB
C
195 lines
18 KiB
C
|
#ifndef REALTEK_POWER_SEQUENCE_8723D
|
||
|
|
#define REALTEK_POWER_SEQUENCE_8723D
|
||
|
|
|
||
|
|
/* #include "PwrSeqCmd.h" */
|
||
|
|
#include "HalPwrSeqCmd.h"
|
||
|
|
|
||
|
|
/*
|
||
|
|
Check document WM-20110607-Paul-RTL8192e_Power_Architecture-R02.vsd
|
||
|
|
There are 6 HW Power States:
|
||
|
|
0: POFF--Power Off
|
||
|
|
1: PDN--Power Down
|
||
|
|
2: CARDEMU--Card Emulation
|
||
|
|
3: ACT--Active Mode
|
||
|
|
4: LPS--Low Power State
|
||
|
|
5: SUS--Suspend
|
||
|
|
|
||
|
|
The transition from different states are defined below
|
||
|
|
TRANS_CARDEMU_TO_ACT
|
||
|
|
TRANS_ACT_TO_CARDEMU
|
||
|
|
TRANS_CARDEMU_TO_SUS
|
||
|
|
TRANS_SUS_TO_CARDEMU
|
||
|
|
TRANS_CARDEMU_TO_PDN
|
||
|
|
TRANS_ACT_TO_LPS
|
||
|
|
TRANS_LPS_TO_ACT
|
||
|
|
|
||
|
|
TRANS_END
|
||
|
|
*/
|
||
|
|
#define RTL8723D_TRANS_CARDEMU_TO_ACT_STEPS 27
|
||
|
|
#define RTL8723D_TRANS_ACT_TO_CARDEMU_STEPS 8
|
||
|
|
#define RTL8723D_TRANS_CARDEMU_TO_SUS_STEPS 7
|
||
|
|
#define RTL8723D_TRANS_SUS_TO_CARDEMU_STEPS 5
|
||
|
|
#define RTL8723D_TRANS_CARDEMU_TO_CARDDIS_STEPS 8
|
||
|
|
#define RTL8723D_TRANS_CARDDIS_TO_CARDEMU_STEPS 7
|
||
|
|
#define RTL8723D_TRANS_CARDEMU_TO_PDN_STEPS 4
|
||
|
|
#define RTL8723D_TRANS_PDN_TO_CARDEMU_STEPS 1
|
||
|
|
#define RTL8723D_TRANS_ACT_TO_LPS_STEPS 13
|
||
|
|
#define RTL8723D_TRANS_LPS_TO_ACT_STEPS 11
|
||
|
|
#define RTL8723D_TRANS_END_STEPS 1
|
||
|
|
|
||
|
|
|
||
|
|
#define RTL8723D_TRANS_CARDEMU_TO_ACT \
|
||
|
|
/* format */ \
|
||
|
|
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, / comments here*/ \
|
||
|
|
{0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)}, /*0x20[0] = 1b'1 enable LDOA12 MACRO block for all interface*/ \
|
||
|
|
{0x0067, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0}, /*0x67[0] = 0 to disable BT_GPS_SEL pins*/ \
|
||
|
|
{0x0001, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 1, PWRSEQ_DELAY_MS},/*Delay 1ms*/ \
|
||
|
|
{0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(5), 0}, /*0x00[5] = 1b'0 release analog Ips to digital ,1:isolation*/ \
|
||
|
|
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, (BIT(4) | BIT(3) | BIT2), 0},/* disable SW LPS 0x04[10]=0 and WLSUS_EN 0x04[11]=0*/ \
|
||
|
|
{0x0075, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0) , BIT(0)},/* Disable USB suspend */ \
|
||
|
|
{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), BIT(1)},/* wait till 0x04[17] = 1 power ready*/ \
|
||
|
|
{0x0075, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0) , 0},/* Enable USB suspend */ \
|
||
|
|
{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)},/* release WLON reset 0x04[16]=1*/ \
|
||
|
|
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, (BIT(1) | BIT(0)), 0}, \
|
||
|
|
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 0},/* disable HWPDN 0x04[15]=0*/ \
|
||
|
|
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, (BIT(4) | BIT(3)), 0},/* disable WL suspend*/ \
|
||
|
|
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)},/* polling until return 0*/ \
|
||
|
|
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(0), 0},/**/ \
|
||
|
|
{0x0010, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(6), BIT(6)},/* Enable WL control XTAL setting*/ \
|
||
|
|
{0x0049, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)},/*Enable falling edge triggering interrupt*/\
|
||
|
|
{0x0063, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)},/*Enable GPIO9 interrupt mode*/\
|
||
|
|
{0x0062, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), 0},/*Enable GPIO9 input mode*/\
|
||
|
|
{0x0058, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)},/*Enable HSISR GPIO[C:0] interrupt*/\
|
||
|
|
{0x005A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)},/*Enable HSISR GPIO9 interrupt*/\
|
||
|
|
{0x0068, PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3), BIT(3)},/*For GPIO9 internal pull high setting by test chip*/\
|
||
|
|
{0x0069, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(6), BIT(6)},/*For GPIO9 internal pull high setting*/\
|
||
|
|
{0x0073, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(2), BIT(2)},/*GNT Controlled by Wifi*/\
|
||
|
|
{0x001f, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00},/*reset RF path S1*/\
|
||
|
|
{0x0077, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00},/*reset RF path S0*/\
|
||
|
|
{0x001f, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x07},/*enable RF path S1*/\
|
||
|
|
{0x0077, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x07},/*enalbe RF path S0*/\
|
||
|
|
|
||
|
|
|
||
|
|
#define RTL8723D_TRANS_ACT_TO_CARDEMU \
|
||
|
|
/* format */ \
|
||
|
|
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, / comments here*/ \
|
||
|
|
/*{0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0}, */ /*0x1F[7:0] = 0 turn off RF*/ \
|
||
|
|
{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0}, /*0x2[0]=0 Reset BB, RF enter Power Down mode*/ \
|
||
|
|
{0x0049, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), 0},/*Enable rising edge triggering interrupt*/ \
|
||
|
|
{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)},/* release WLON reset 0x04[16]=1*/ \
|
||
|
|
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)}, /*0x04[9] = 1 turn off MAC by HW state machine*/ \
|
||
|
|
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), 0}, /*wait till 0x04[9] = 0 polling until return 0 to disable*/ \
|
||
|
|
{0x0010, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(6), 0},/* Enable BT control XTAL setting*/\
|
||
|
|
{0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(5), BIT(5)}, /*0x00[5] = 1b'1 analog Ips to digital ,1:isolation*/ \
|
||
|
|
{0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0}, /*0x20[0] = 1b'0 disable LDOA12 MACRO block*/\
|
||
|
|
|
||
|
|
|
||
|
|
#define RTL8723D_TRANS_CARDEMU_TO_SUS \
|
||
|
|
/* format */ \
|
||
|
|
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, / comments here*/ \
|
||
|
|
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4) | BIT(3), (BIT4 | BIT3)}, /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \
|
||
|
|
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(4), BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/ \
|
||
|
|
{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4)}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/ \
|
||
|
|
{0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07[7:0] = 0x20 SDIO SOP option to disable BG/MB/ACK/SWR*/ \
|
||
|
|
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(4), BIT3 | BIT4}, /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \
|
||
|
|
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), BIT(0)}, /*Set SDIO suspend local register*/ \
|
||
|
|
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), 0}, /*wait power state to suspend*/
|
||
|
|
|
||
|
|
#define RTL8723D_TRANS_SUS_TO_CARDEMU \
|
||
|
|
/* format */ \
|
||
|
|
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, / comments here*/ \
|
||
|
|
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(7), 0}, /*clear suspend enable and power down enable*/ \
|
||
|
|
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), 0}, /*Set SDIO suspend local register*/ \
|
||
|
|
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), BIT(1)}, /*wait power state to suspend*/\
|
||
|
|
{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0}, /*0x23[4] = 1b'0 12H LDO enter normal mode*/ \
|
||
|
|
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(4), 0}, /*0x04[12:11] = 2b'01enable WL suspend*/
|
||
|
|
|
||
|
|
|
||
|
|
#define RTL8723D_TRANS_CARDEMU_TO_CARDDIS \
|
||
|
|
/* format */ \
|
||
|
|
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, / comments here*/ \
|
||
|
|
{0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07 = 0x20 , SOP option to disable BG/MB*/ \
|
||
|
|
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(4), BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/ \
|
||
|
|
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(2), BIT(2)}, /*0x04[10] = 1, enable SW LPS*/ \
|
||
|
|
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(4), BIT3 | BIT4}, /*0x04[12:11] = 2b'11 enable WL suspend*/ \
|
||
|
|
{0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 1}, /*0x48[16] = 1 to enable GPIO9 as EXT WAKEUP*/ \
|
||
|
|
{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4)}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/ \
|
||
|
|
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), BIT(0)}, /*Set SDIO suspend local register*/ \
|
||
|
|
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), 0}, /*wait power state to suspend*/
|
||
|
|
|
||
|
|
#define RTL8723D_TRANS_CARDDIS_TO_CARDEMU \
|
||
|
|
/* format */ \
|
||
|
|
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, / comments here*/ \
|
||
|
|
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(7), 0}, /*clear suspend enable and power down enable*/ \
|
||
|
|
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), 0}, /*Set SDIO suspend local register*/ \
|
||
|
|
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), BIT(1)}, /*wait power state to suspend*/\
|
||
|
|
{0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0}, /*0x48[16] = 0 to disable GPIO9 as EXT WAKEUP*/ \
|
||
|
|
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(4), 0}, /*0x04[12:11] = 2b'01enable WL suspend*/\
|
||
|
|
{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0}, /*0x23[4] = 1b'0 12H LDO enter normal mode*/ \
|
||
|
|
{0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0},/*PCIe DMA start*/
|
||
|
|
|
||
|
|
|
||
|
|
#define RTL8723D_TRANS_CARDEMU_TO_PDN \
|
||
|
|
/* format */ \
|
||
|
|
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, / comments here*/ \
|
||
|
|
{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4)}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/ \
|
||
|
|
{0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK | PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07[7:0] = 0x20 SOP option to disable BG/MB/ACK/SWR*/ \
|
||
|
|
{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0},/* 0x04[16] = 0*/\
|
||
|
|
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), BIT(7)},/* 0x04[15] = 1*/
|
||
|
|
|
||
|
|
#define RTL8723D_TRANS_PDN_TO_CARDEMU \
|
||
|
|
/* format */ \
|
||
|
|
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, / comments here*/ \
|
||
|
|
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 0},/* 0x04[15] = 0*/
|
||
|
|
|
||
|
|
#define RTL8723D_TRANS_ACT_TO_LPS \
|
||
|
|
/* format */ \
|
||
|
|
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, / comments here*/ \
|
||
|
|
{0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF},/*PCIe DMA stop*/ \
|
||
|
|
{0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF},/*Tx Pause*/ \
|
||
|
|
{0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
|
||
|
|
{0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
|
||
|
|
{0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
|
||
|
|
{0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
|
||
|
|
{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0},/*CCK and OFDM are disabled, and clock are gated*/ \
|
||
|
|
{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/ \
|
||
|
|
{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), 0},/*Whole BB is reset*/ \
|
||
|
|
{0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x03},/*Reset MAC TRX*/ \
|
||
|
|
{0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), 0},/*check if removed later*/ \
|
||
|
|
{0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00},/*When driver enter Sus/ Disable, enable LOP for BT*/ \
|
||
|
|
{0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(5), BIT(5)},/*Respond TxOK to scheduler*/ \
|
||
|
|
|
||
|
|
|
||
|
|
#define RTL8723D_TRANS_LPS_TO_ACT \
|
||
|
|
/* format */ \
|
||
|
|
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, / comments here*/ \
|
||
|
|
{0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, 0xFF, 0x84}, /*SDIO RPWM*/\
|
||
|
|
{0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84}, /*USB RPWM*/\
|
||
|
|
{0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84}, /*PCIe RPWM*/\
|
||
|
|
{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, /*Delay*/\
|
||
|
|
{0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0}, /*. 0x08[4] = 0 switch TSF to 40M*/\
|
||
|
|
{0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(7), 0}, /*Polling 0x109[7]=0 TSF in 40M*/\
|
||
|
|
{0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(6) | BIT(7), 0}, /*. 0x29[7:6] = 2b'00 enable BB clock*/\
|
||
|
|
{0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)}, /*. 0x101[1] = 1*/\
|
||
|
|
{0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF}, /*. 0x100[7:0] = 0xFF enable WMAC TRX*/\
|
||
|
|
{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1) | BIT(0), BIT1 | BIT0}, /*. 0x02[1:0] = 2b'11 enable BB macro*/\
|
||
|
|
{0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0}, /*. 0x522 = 0*/
|
||
|
|
|
||
|
|
#define RTL8723D_TRANS_END \
|
||
|
|
/* format */ \
|
||
|
|
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, / comments here*/ \
|
||
|
|
{0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, 0, PWR_CMD_END, 0, 0},
|
||
|
|
|
||
|
|
|
||
|
|
extern WLAN_PWR_CFG rtl8723D_power_on_flow[RTL8723D_TRANS_CARDEMU_TO_ACT_STEPS + RTL8723D_TRANS_END_STEPS];
|
||
|
|
extern WLAN_PWR_CFG rtl8723D_radio_off_flow[RTL8723D_TRANS_ACT_TO_CARDEMU_STEPS + RTL8723D_TRANS_END_STEPS];
|
||
|
|
extern WLAN_PWR_CFG rtl8723D_card_disable_flow[RTL8723D_TRANS_ACT_TO_CARDEMU_STEPS + RTL8723D_TRANS_CARDEMU_TO_CARDDIS_STEPS + RTL8723D_TRANS_END_STEPS];
|
||
|
|
extern WLAN_PWR_CFG rtl8723D_card_enable_flow[RTL8723D_TRANS_CARDDIS_TO_CARDEMU_STEPS + RTL8723D_TRANS_CARDEMU_TO_ACT_STEPS + RTL8723D_TRANS_END_STEPS];
|
||
|
|
extern WLAN_PWR_CFG rtl8723D_suspend_flow[RTL8723D_TRANS_ACT_TO_CARDEMU_STEPS + RTL8723D_TRANS_CARDEMU_TO_SUS_STEPS + RTL8723D_TRANS_END_STEPS];
|
||
|
|
extern WLAN_PWR_CFG rtl8723D_resume_flow[RTL8723D_TRANS_SUS_TO_CARDEMU_STEPS + RTL8723D_TRANS_CARDEMU_TO_ACT_STEPS + RTL8723D_TRANS_END_STEPS];
|
||
|
|
extern WLAN_PWR_CFG rtl8723D_hwpdn_flow[RTL8723D_TRANS_ACT_TO_CARDEMU_STEPS + RTL8723D_TRANS_CARDEMU_TO_PDN_STEPS + RTL8723D_TRANS_END_STEPS];
|
||
|
|
extern WLAN_PWR_CFG rtl8723D_enter_lps_flow[RTL8723D_TRANS_ACT_TO_LPS_STEPS + RTL8723D_TRANS_END_STEPS];
|
||
|
|
extern WLAN_PWR_CFG rtl8723D_leave_lps_flow[RTL8723D_TRANS_LPS_TO_ACT_STEPS + RTL8723D_TRANS_END_STEPS];
|
||
|
|
|
||
|
|
#endif
|